Excellent corrosion resistance, ideal for corrosive liquids and various chemical solutions. Measurement under severe conditions is possible.

Corresponding to the corrosive liquid and various chemical liquid float type level gauge of the resin type

  • Excellent corrosion resistance, ideal for measuring liquid level of corrosive liquids and various chemical liquids.
  • Stable liquid level measurement is possible even under severe conditions.
  • It also supports changes in electrical properties of the object to be measured.
    ■ Ideal for liquid surface management of corrosive liquids and various chemical liquids.
    ■ It can be used with simple initial setting (one touch push button).
    ■ The dead zone can be greatly reduced, and it is possible to measure with a wide range of sensors.

Line-up according to specifications such as standard flange connection, helir connection, threaded connection etc. are available.

Need more information?

Please contact +6221-5467618, +6221-54212399 or email sales[email protected]


1. has excellent corrosion resistance
adopt a superior resin in corrosion to the sensor unit (PVC, PP, etc.). It corresponds to various chemical liquids.

2. for a wide range of the object to be measured
does not affect the electrical properties change of the object to be measured. It is not affected by pressure and gas components.

3. Safe design withstand the harsh tank conditions
waterproof housing (protection class IP68).

4. Available in a simple setting
can be measured with a simple initial setup (one-touch push-button). The undetectable part can be greatly reduced, and it can be measured in a wide range of degrees of freedom.

5. standard equipment each function for stable measurement
standard equipment such as a delay setting function and the watchdog function.


Use  Remaining amount measurement (level meter / level meter)
Measured object  Liquid / bubble neglect
Detailed measurement item  Distilled water / Distilled water / Alcohol / Pure water, Ultra pure water / Corrosive liquid / Medicinal solution (acid / alkali) / Cleaning fluid / Oil (non explosion) Working oil / Waste liquid / Foam neglect detection
Contact / non-contact  contact
Measuring method  Float type
Explosion proof  None (non-explosion-proof)
Tank size  Medium size (drum size)
Mounting position  Vertical (from above)
Detailed measurement environment  Water supply control to elevated tanks such as buildings and condominiums, drainage control of drain tanks / raw material level control / underground pits / wide liquids (even when the type of liquid changes or the electric properties of liquid changes) Possible) / water level monitoring of water supply and sewerage


Amplifier section

Power supply AC / DC 20 to 250 V
Power consumption 1.5 VA or less
Operating ambient temperature -10 ° C to + 60 ° C
output 4.0 mA output for 0% stored value, 20.0 mA output for 100% stored value, output limit 0.02 mA (about -25%) to 20.46 mA (about 102%), 4 to 20 mA (maximum load 500 Ω or less)
Measurement accuracy ± 8 mm
Response speed (delay) About 0.5 to 180 seconds variable
Protection grade IP68
Wiring port G1 / 2
option RS485 communication


Size JIS 5K 50 A FF (It can be changed by request)
Material PVC
option The connection part can be changed (various flanges, including various screws), material can be changed (SUS 316)


Outer Diameter Φ 48 × H 50
Material PP
Specific gravity of measurable liquid 0.65 or more


Outer Diameter Φ22 mm
Material PVC
L dimension (max) Maximum 2000 mm ※ It may become shorter depending on usage environment. For actual maximum dimensions, please contact our sales representative.

Float Other

Operating ambient temperature -10 ° C to + 50 ° C
Detection pitch Maximum 8 mm
Dead zone For specific gravity 1.0 Stem tip 70 mm and case side 30 mm
Allowable pressure 0.2 MPa * Depending on the withstand pressure of the connection part when the connection part withstand voltage is below this value.
Protection grade IP68
option Wave barrier, oil prohibition treatment, electrolytic polishing, buffing finish (# 400)